Egerlandstr. 13, 91058 Erlangen
Tel.: 09131/85-20838
Fax: 09131/85-27141
Mail address:
This e-mail address is being protected from spambots. You need JavaScript enabled to view it
Executive Director DFG Transregional Collaborative Research Center 73
Secretary of ESAFORM
Editor of the journal Production Engineering
Member of the DFG Collaborative Research Center 814
Member of the DFG Transregional Collaborative Research Center 285
Member of the Graduate School of Advanced Optical Technologies
Member of the Center for Management Technology and Society (CMTS)
Prakash, V.; Kumar, D. R.; Horn, A.; Hagenah, H.; Merklein, M.:
Modeling material behavior of AA5083 aluminum alloy sheet using biaxial tensile tests and its application in numerical simulation of deep drawing.
International Journal of Advanced Manufacturing Technology 106(2020), pp. 1133-1148
Rohrmoser, A.; Heling, B.; Schleich, B.; Hagenah, H.; Wartzack, S.; Merklein, M.:
Ausgewählte Einflussgrößen auf die erzielbaren Verzahnungstoleranzen beim Kaltfließpressen.
In: Sandro Wartzack (ed.) (Edtr.): Summer School Toleranzmanagement - Beiträge zur 4. Summer School - September 2020, Druck+Verlag Ernst Vögel GmbH, 2020, pp. 99-106
Schubert, D.; Rohrmoser, A.; Hagenah, H.; Merklein, M.; Drummer, D.:
Verschleißmodellierung am Beispiel einer Polyamid-Stahl-Getriebepaarung für das prozessorientierte Toleranzmanagement.
In: Sandro Wartzack (ed.) (Edtr.): Summer School Toleranzmanagement - Beiträge zur 4. Summer School - September 2020, Druck+Verlag Ernst Vögel GmbH, 2020, pp. 107-116
Rohrmoser, A.; Hagenah, H.; Merklein, M.:
Adapted tool design for the cold forging of gears from non-ferrous and light metals.
The International Journal of Advanced Manufacturing Technology, DOI: 10.1007/s00170-020-06449-6 (2020), accepted
Hagenah, H.; Schulte, R.; Vogel, M.; Herrmann, J.; Scharrer, H.; Lechner, M.; Merklein, M.:
4.0 in metal forming - questions and challenges.
Procedia CIRP 79(2019), pp. 649-654
Heling, B.; Oberleiter, T.; Rohrmoser, A.; Kiener, C.; Schleich, B.; Hagenah, H.; Merklein, M.; Willner, K.; Wartzack, S.:
Berücksichtigung von produktionsspezifischen Abweichungen im interdisziplinären Toleranzmanagement.
In: S. Wartzack (Edtr.): Industriekolloquium der Forschungsgruppe FOR 2271, Druck+Verlag Ernst Vögel GmbH, 2019, pp. 36-45
Schubert, D.; Rohrmoser, A.; Hagenah, H.; Merklein, M.; Drummer, D.:
Einfluss der fertigungsbedingten Gestalt und Struktur auf das Einlaufverhalten von Stahl-Kunststoff-Getriebepaarungen.
In: S. Wartzack (Edtr.): Industriekolloquium der Forschungsgruppe FOR 2271, Druck+Verlag Ernst Vögel GmbH, 2019, pp. 74-84
Rohrmoser, A.; Hagenah, H.; Merklein, M.:
Berücksichtigung funktionsrelevanter Gestaltabweichungen bei der Auslegung von Umformprozessen zur Herstellung von Stirnrädern mit Sonderverzahung durch Fließpressen.
In: S. Wartzack (Edtr.): Industriekolloquium der Forschungsgruppe FOR 2271, Druck+Verlag Ernst Vögel GmbH, 2019, pp. 26-29
Rohrmoser, A.; Heling, B.; Schleich, B.; Kiener, C.; Hagenah, H.; Wartzack, S.; Merklein, M.:
A methodology for the application of virtual evaluation methods within the design process of cold forged steel pinions.
In: (Edtr.): Proceedings of the 22nd International Conference on Engineering Design (ICED19), Delft, The Netherlands, 5-8 August 2019, 2019, pp. 3451-3460
Rohrmoser, A.; Kiener, C.; Hagenah, H.; Merklein, M.:
Einsatz numerischer Analysetools bei der Auslegung und Herstellung kaltfließgepresster Stahlzahnräder.
Zeitschrift Konstruktion (2019)4, pp. 85-90
Heling, B.; Oberleiter, T.; Rohrmoser, A.; Kiener, C.; Schleich, B.; Hagenah, H.; Merklein, M.; Willner, K.; Wartzack, S.:
A concept for process-oriented interdisciplinary tolerance management considering production-specific deviations.
In: (Edtr.): Proceedings of the 22nd International Conference on Engineering Design (ICED19), Delft, The Netherlands, 5-8 August 2019, 2019, pp. 3441-3450
Schubert, D.; Herle, S.; Rohrmoser, A.; Hagenah, H.; Merklein, M.; Drummer, D.:
New Approach on the Allocation of Wear Allowances - a Case Study.
In: (Edtr.): Proceedings of the 22nd International Conference on Engineering Design (ICED19), Delft, The Netherlands, 5-8 August 2019, 2019, pp. 3511-3520
Duflou, J.R:; Carette, Y.; Fratini, L.; Micari, F.; Merklein, M.; Hagenah, H. (Edtr.):
18th International Conference on Sheet Metal, SHEMET 2019.
Elsevier, 2019
Rohrmoser, A.; Kiener, C.; Schubert, D.; Hagenah, H.; Drummer, D.; Merklein, M.:
Gezielte Beeinflussung der einsatzrelevanten Bauteileigenschaften kaltfließgepresster Zahnräder.
Zeitschrift Konstruktion (2019)07-08, pp. 94-98
Rohrmoser, A.; Kiener, C.; Hagenah, H.; Merklein, M.:
Influence of tribological conditions on application relevant component properties of cold forged gears.
Production Engineering 13(2019)5, pp. 579-588
Prakash, V.; Kumar, D. R.; Merklein, M.; Hagenah, H.:
Numerical simulation of hydraulic bulging using uniaxial and biaxial flow curves and different yield criteria.
IOP Conference Series Materials Science and Engineering 652(2019)1, pp. 012038
Lorenz, R.; Hagenah, H.; Merklein, M.:
Influence of the Coating Process on the Tribological Conditions during Cold Forging with a MoS2 Based Lubricant.
AIP Conference Proceedings; https://doi.org/10.1063/1.5034867 1960(2018)1, 04001, published online
Lorenz, R.; Hagenah, H.; Merklein, M.:
Experimental evaluation of cold forging lubricants using double cup extrusion tests.
Materials Science Forum 918(2018), pp. 65-70
Papke, T.; Huber, F.; Hagenah, H.; Schmidt, M.; Merklein, M.:
Potentiale der Kombination von Umformtechnik und additiver Fertigung in hybriden Prozessketten.
In: Drummer, D. (Edtr.): 6. Industriekolloquium des Sonderforschungsbereichs 814 - Additive Fertigung, Print Line, 2018, pp. 59-76
Merklein, M.; Hagenah, H.:
Introduction to sheet-bulk metal forming.
Production Engineering 10(2016)1, pp. 1-3
Purr, S.; Wendt, A.; Meinhardt, J.; Moelzl, K.; Werner, A.; Hagenah, H.; Merklein, M.:
Data-driven inline optimization of the manufacturing process of car body parts.
IOP Conf. Series: Materials Science and Engineering 159(2016)1, pp. 012002
Hagenah, H.; Merklein, M.; Lechner, M.; Schaub, A.; Lutz, S.:
Determination of the mechanical properties of hot stamped parts from numerical simulations.
Procedia CIRP 33(2015), pp. 167-172
Merklein, M.; Duflou, J.; Leacock. A.; Micari, F.; Hagenah, H. (Edtr.):
Sheet Metal 2015, Proceedings of the 16th international conference on sheet metal.
Trans Tech Publ., 2015
Hagenah, H.; Geiger, M.:
Laser Adjustment Using Actuators.
In: A. Erman Tekkaya, Werner Homberg, Alexander Brosius (Edtr.): 60 Excellent Inventions in Metal Forming, Springer, 2015, pp. 167-172
Plettke, R.; Vipavc, D.; Grüner, M.; Hagenah, H.; Merklein, M.:
The influence of the annealing process in the fabrication of helical needles for the suture in deep wound cavities.
Int. J. Computer Integrated Manufacturing 27(2014)10, pp. 960-967
Tsoupis, I.; Hildering, S.; Hagenah, H.; Merklein, M.:
Werkstoffschädigung in der Prozesskette Schneiden - Biegen.
In: Liewald, M.; Tekkaya, A. E. (Edtrs.): 17. Workshop Simulation in der Umformtechnik, Institut für Umformtechnik, Universität Stuttgart, 2014, pp. 73-89
Merklein, M.; Franke, J.; Hagenah, H. (Edtr.):
WGP Congress 2014, Progress in Production Engineering.
Trans Tech Publ., 2014
Hagenah, H.; Böhm, W.; Breitsprecher, T.; Merklein, M.; Wartzack, S.:
Modelling, Construction and Manufacture of a Lightweight Robot Arm.
Procedia CIRP 12(2013), pp. 211-216
Lechner, M.; Kuppert, A.; Hagenah, H.; Merklein, M.:
Optimization of the heat treatment layout and blank outline of THTB.
Key Eng. Mater. 554-557(2013), pp. 2465-2471
Merklein, M.; Hagenah, H.; Kaupper, M.; Schaub, A.:
Mechanical response of Ti-6Al-4V alloy on deformation at moderate temperatures.
Key Eng. Mater. 549 (2013), pp. 311-316
Merklein, M.; Hagenah, H.; Kaupper, M.; Schaub, A.:
Analysis of the deformation behavior of Ti-6Al-4V at elevated temperatures.
Key Eng. Mater. 554-557 (2013), pp. 29-32
Merklein, M.; Hagenah, H.; Lechner, M.; Kuppert, A.:
Simulationsgestützte Auslegung maßgeschneiderter wärmebehandelter Aluminiumhalbzeuge.
In: Tekkaya A. E.; Liewald M. (Edtrs.): 16. Workshop Simulation in der Umformtechnik, Institut für Umformtechnik und Leichtbau, Technische Universität Dortmund, 2013, pp. 90-101
Hagenah, H.; Geiger, M.; Merklein, M.:
Numerical simulation to improve robustness in sheet metal forming process chains.
AIP Conf. Proc. 1532(2013), pp. 683 - 688
Merklein, M.; Franke, J.; Hagenah, H. (Edtr.):
WGP Congress 2013, Progress in Production Engineering.
Trans Tech Publ., 2013
Merklein, M.; Hagenah, H.; Schneider, T.:
Sheet-Bulk Metal Forming Processes - State of the Art and its Perspectives.
In: Kolleck, R. (Edtr.): TTP 2013 - Tools and Technologies for Processing Ultra High Strength Materials, Verlag der TU Graz, 2013, pp. 197-204
Merklein, M.; Hagenah, H.; Schneider, T.:
Blechmassivumformung - Stand der Technik und Ausblick.
In: Merklein, M.; Behrens, B. A., Tekkaya, A. E. (Edtrs.): 2. Workshop Blechmassivumformung, Meisenbach, 2013, pp. 1-10
Li, H.; Dong, X.; Shen, Y.; Zhou, R.; Diehl, A.; Hagenah, H.; Engel, U.; Merklein, M.; Cao, J.:
Analysis of microbending of CuZn37 brass foils based on strain gradient hardening models.
J. Mater. Process. Technol. 212(2012)3, pp. 653-661
Li, H.; Dong, X.; Huang, S.; Diehl, A.; Hagenah, H.:
Material Intrinsic Length in Plastic Strain Gradient Theory and Microbending Process of Metal Foils.
Adv. Mater. Res. 403-408(2012), pp. 685-690
Merklein, M.; Hagenah, H. (Edtr.):
Proc. 15th ESAFORM Conference Part 1 & 2.
Trans Tech Publications, 2012
Merklein, M.; Allwood, J. M.; Behrens, B.; Brosius, A.; Hagenah, H.; Kuzman, K.; Mori, K.; Tekkaya, E.; Weckenmann, A.:
Bulk forming of sheet metal.
Annals of the CIRP 61(2012)2, pp. 725-745
Plettke, R.; Vipavc, D.; Grüner, M.; Hagenah, H.; Merklein, M.:
Prototype Manufacturing of Helical Needles for Suture in Deep Wound Cavities.
In: E. Ceretti, A. Fiorentino, L. Giorleo, C. Giardini (Edtr.): Proc. 1st Int.Conf. Design and Processes for medical devices PROMED, NEOS EDIZIONI srl, 2012, pp. 191-194
Li, H.; Dong, X.; Wang, Q.; Shen, Y.; Diehl, A.; Hagenah, H.; Engel, U.; Merklein, M.:
Determination of material intrinsic length and strain gradient hardening in microbending process.
International Journal of Solids and Structures 48(2011)1, pp. 163-174
Li, H.; Dong, X.; Wang, Q.; Shen, Y.; Diehl, A.; Hagenah, H.; Engel, U.; Merklein, M.:
Size effects of CuZn37 brass foil in microforming.
Material Science and Technology 19(2011)4, pp. 15-19
Li, H. Z.; Dong, X. H.; Shen, Y.; Diehl, A.; Hagenah, H.; Engel, U.; Merklein, M.:
Size effects on springback behaviors due to plastic strain gradient hardening in microbending process of pure aluminum foils.
Journal of Materials Science and Engineering A 257(2010)16-17, pp. 4497-4504
Plettke, R.; Vatter, P.; Vipavc, D.; Cojutti, M.; Hagenah, H.:
Investigation on the Process Parameters and Process Window of "Three-Roll-Push-Bending".
In: Hinduja, S.; Li, L. (Edtrs.): Proc. 36th Matador Conf., Springer, 2010, pp. 25-28
Li, H.; Dong, X.; Huang, S.; Diehl, A.; Hagenah, H.:
Material intrinsic length in plastic strain gradient theory and microbending process of metal foils.
In: (Edtr.): 6th International conference on MEMS NANO, and Smart Systems (ICMENS 2010), 2010, pp. 218-211
Hagenah, H.; Vipavc, D.; Plettke, R.; Merklein, M.:
Numerical Model of Tube Freeform Bending by Three-Roll-Push-Bending.
In: Associacao Portuguesa de Mecanica Teória, Aplicada e Computacional (Edtrs.): 2nd International Conference on Engineering Optimization, 2010, published on CD
Hagenah, H.; Vipavc, D.; Vatter, P.; Cojutti, M.; Plettke, R.:
Creation of the Data Base for the Process Design of the Three-Roll-Push Bending Process.
In: Teti, R. (Edtr.): 7th CIRP Int. Conf. Intelligent Computation in Manufacturing Engineering, 2010, pp. 259-264
Merklein, M.; Hagenah, H.; Cojutti, M.:
Investigations on Three-Roll Bending of Plain Tubular Components.
Key Eng. Mater. 410-411(2009), pp. 325-334
Geiger, M.; Plettke, R.; Hagenah, H.:
Multi-Objective Optimization of Actuator System Design for Laser Micro Adjustment.
Production Engineering 3(2009)2, pp. 181-188
Plettke, R.; Hagenah, H.; Geiger, M.:
Application of genetic algorithms for the optimisation of actuator systems for laser micro adjustment..
International Journal of Microstructure and Materials Properties (IJMMP) 4(2009)6, pp. 615-625
Cojutti, M.; Vipavc, D.; Hagenah, H.; Merklein, M.:
An innovative approach for the process design for three-roll bending of plain tubular components.
In: Angeles Gutierrez, M.; Sedlmaier, A.; Galdós, L. (Edtrs.): Proc. 1st Int. Congress on Roll Forming, 2009, pp. 133-139
Li, H. Z.; Dong, X. H.; Shen, Y.; Diehl, A.; Hagenah, H.; Engel, U.; Merklein, M.:
Influence of the plasticity strain gradient on springback in micro-bending process of metal foils.
In: Chinese Society of Mechanical Engineering (Edtr.): Proceedings of The 2nd Asia Conference on micro/nano sized technology (AWMFT-2009), 2009, pp. 602-606
Hagenah, H.; Schmidt, M.; Klämpfl, F.:
Planning the use of high-power excimer laser for psoriasis treatment.
In: Mitsuishi, M.; Ueda, K.; Kimura, F. (Edtrs.): Manufacturing Systems and Technologies for the New Frontier - The 41st CIRP Conference on Manufacturing Systems, Springer, 2008, pp. 349-354
Geiger, M.; Klämpfl, F.; Hagenah, H.:
Automated online planning of localized laser process parameters using simulated annealing.
Production Engineering 2(2008)2, pp. 171-178
Klämpfl, F.; Hagenah, H.:
Algorithmen zum simulationsbasierten, pulsgenauen Planen von Laserbestrahlungen.
In: Schulze, T.; Preim, B. (Edtrs.): Simulation und Visualisierung 2008. Proceedings of the 19th Conference on Simulation and Visualization (SimVis), SCS Publishing House e.V., 2008, pp. 41-52
Klämpfl, F.; Schmidt, M.; Hagenah, H.:
Intelligent irradiation planning for new laser applications.
In: De Vin, L. (Edtr.): Proceedings of the 18th International Conference on Flexible Automation and Intelligent Manufacturing (FAIM 2008), Runit AB, 2008, pp. 924-930
Merklein, M.; Geiger, M.; Hagenah, H.; Cojutti, M.:
3-Rollen-Schubbiegen zur flexiblen Herstellung freiformgebogener Rohrleitungen.
Zukunftstechnologien in Bayern (2008), pp. 24-26
Hagenah, H.; Plettke, R.; Klämpfl, F.:
Fast, problem specific approaches for the evaluation of laser beam propagation in process planning.
In: Teti, R. (Edtr.): Proceedings of the 6th CIRP International Conference on Intelligent Computation in Manufacturing Engineering, Edizioni Zino, 2008, pp. 413-418
Plettke, R.; Hagenah, H.; Geiger, M.:
Developing a computer aided design system for actuator design for laser micro adjustment.
In: (Edtr.): Proceedings of the 18th CIRP International Design Seminar (March 2008), 2008, pp. 1-5
Hagenah, H.; Plettke, R.; Geiger, M.:
Algorithms for Planning and Control of Laser Forming.
In: Vollertsen, F. (Edtr.): Proceedings of the IWOTE 08, BIAS Verlag, 2008, pp. 191-203
Klämpfl, F.; Hagenah, H.:
Algorithms for pulsewise irradiation planning.
In: Geiger, M.; Otto, A.; Schmidt, M. (Edtrs.): Proceedings of the LANE 2007, Meisenbach, 2007, pp. 877-886
Tang, B. T.; Zhao, Z.; Hagenah, H.; Lu, X. L.:
Energy based algorithms to solve initial solution in one-step finite element method of sheet metal stamping.
Comput. Methods Appl. Mech. Engrg. 196(2007), pp. 2187-2196
Plettke, R.; Hagenah, H.; Geiger, M.:
Application of genetic algorithms for the optimization of actuator systems for laser micro adjustment.
In: Kuzman, K. (Edtr.): Proceedings of the 6th International Conference on Industrial Tools and Material Processing Technologies 2007 (ICIT&MPT 2007), 2007, pp. 297-302
Plettke, R.; Hagenah, H.; Geiger, M.:
Computer assisted design of complex actuator systems for laser micro adjustment.
In: Geiger, M.; Otto, A.; Schmidt, M. (Edtrs.): Proceedings of the LANE 2007, Meisenbach, 2007, pp. 533-544
Plettke, R.; Hagenah, H.; Geiger, M.:
Computer assisted design of actuator systems for laser micro adjustment.
Key Eng. Mater. 344(2007), pp. 807-814
Plettke, R.; Hagenah, H.; Geiger, M.:
Rechnergestützter Entwurf von Aktorsystemen für die lasergebundene Mikrojustage.
In: Schulze, T.; Preim, B.; Schumann, H. (Edtrs.): Simulation und Visualisierung 2007. Proceedings of the 18th Conference on Simulation and Visualization (SimVis), SCS Publishing House e.V., 2007, pp. 43-54
Hagenah, H.; Plettke, R.; Geiger, M.:
Planning and Control of Laser Forming Applications.
In: Butala, P.; Hlebanja, G. (Edtrs.): Proceedings of the 39th CIRP International Seminar on Manufacturing Systems, University of Ljubljana, 2006, pp. 359-367
Hagenah, H.; Kohlbauer, R.:
Apllication of fuzzy logic for process design in sheet metal hydroforming.
In: Govekar, E. (Edtr.): Proceedings of the 9th CIRP International Workshop on Modeling of Machining Operations, University of Ljubljana, 2006, pp. 335-342
Klämpfl, F.; Schmidt, M.; Hagenah, H.; Görtler, A.; Wolfsgruber, F.; Lampalzer, R.; Kaudewitz, P.:
Irradiation planning for automated treatment of psoriasis with a high-power excimer laser.
In: SPIE (Edtr.): Photonics West 2006: Integrated Optoelectronic Devices , 2006, published on CD
Hagenah, H.; Geißdörfer, S.:
System for the automatic correction of sheet metal bending angles by means of laser beam forming.
In: Juster, N.; Rosochowski, A (Edtrs.): The 9th International Conference on Metal Forming ESAFORM, Publishing House Akapit, 2006, pp. 235-238
Klämpfl, F.; Schmidt, M.; Hagenah, H.; Geiger, M.:
Algorithms for Irradiation Planning in Medical Laser Applications.
In: Teti, R. (Edtr.): Proceedings of the 5th CIRP International Seminar on Intelligent Computation in Manufacturing Engineering, University of Naples, 2006, pp. 101-106
Geiger, M.; Hagenah, H.:
Der SFB 396 im Überblick- Beiträge zum Berichts- und Industriekolloquium.
In: Geiger, M.; Singer, R. F: (Edtrs.): Robuste, verkürzte Prozessketten für flächige Leichtbauteile: Tagungsband zum Industriekolloquium, Meisenbach, 2006, pp. 1-6
Hagenah, H.; Plettke, R.; Geiger, M.:
Planning and Control of Laser Forming Applications.
In: Butala, P.; Hlebanja, G (Edtrs.): Proceedings of the 39th CIRP International Seminar on Manufacturing Systems, Dept. of Control and Manufacturing Systems, Faculty of Mechanical Engineering, Univ. of Ljubljana, 2006, pp. 359 - 367
Geiger, M.; Hagenah, H.; Hutterer, A.:
Task Specific Registration Algorithmy within the Closed Loop Control of Laser Forming Processes.
Production Engineering. Annals of the German Academic Society for Production Engineering 2(2005)7, pp. 125-130
Hagenah, H.; Wurm, T.:
Problem specific design of actuators for micro adjustment.
Adv. Mater. Res. 6-8(2005), pp. 271-278
Hagenah, H.; Wurm, T.; Geiger, M.:
Computer assisted design of actuators for high precision adjustment in micro technology.
In: Bramley, A.; Brissaud, D.; Coutellier, D.; Mcmahon, C (Edtrs.): Advances in Integrated Design and Manufacturing in Mechanical Engineering, Springer, 2005, pp. 403-416
Hutterer, A.; Hagenah, H.:
Correcting non circular dents by means of laser beam forming.
In: Geiger, M.; Otto, A. (Edtrs.): Laser Assisted Net shape Engineering 4 - Proceedings of the LANE 2004, Meisenbach Verlag, 2004, pp. 1071-1081
Hagenah, H.; Kohlbauer, R.; Geiger, M.:
Knowledge based automated process design using finite element intermediate states.
In: Teti, R. (Edtr.): Proceedings of the 4th CIRP International Seminar on Intelligent Computation in Manufacturing Engineering. ICME' 2004. Sorrento, Italy, CUES, 2004, pp. 295-300
Hagenah, H.; Wurm, T.; Geiger, M.:
Computer assisted design of actuators for high precision adjustment in micro technology.
In: Bramley, An.N.; Culley, S.J.; Dekoninck, E.A.; McMahon, C.A.; Medland, A.J.; Mileham, A.R.; Newnes, L.B.; Owen, G.W. (Edtrs.): Proceedings of the 5th International Conference on Integrated Design and Manufacturing in Mechanical Engineering, University of Bath, 2004, pp. 10
Geiger, M.; Hagenah, H.; Kohlbauer, R.:
Computer assisted, knowledge based process design for sheet metal hydroforming using finite element simulation.
In: Monostori, L. (Edtr.): Enterprises, production networks, University of Budapest, 2004, pp. 67-72
Hutterer, A.; Hagenah, H.; Otto, A.:
Application of a modified ICP-Algorithm in Manufacturing Technology.
In: Ertl, T.; Girod, B.; Greiner, G.; Niemann, H.; Seidel, H. (Edtrs.): 8th International Fall Workshop, IOS Press, 2003, pp. 127-134
Hutterer, A.; Hagenah, H.; Geiger, M.:
Development of an irradiation strategy withing a closed loop control system for the laser adjustment of deformation.
In: The Institute of Control, Automation and Systems Engineers (ICASE) (Edtr.): Proceedings of the 2003 International Conference on Control, Automation and Systems (ICCAS 2003), 2003, pp. 2313-2318
Geiger, M.; Wurm, T.; Hagenah, H.:
Modellierung von Aktoren für das Laserstrahljustieren in der Mikrotechnik.
In: Hohmann, R. (Edtr.): Fortschritte in der Simulationstechnik, Tagungsband des 17. Symposiums Simulationstechnik ASIM 2003, SCS-Europe, 2003, pp. 261-266
Hagenah, H.:
Simulation based Evaluation of the Accuracy for Sheet Metal Bending caused by the Bending Stage Plan.
In: Weber, C.; Bley, H.; Hirt, G. (Edtrs.): Proceedings of the 36th CIRP Seminar on Manufacturing Systems, Progress in Virtual Manufacturing Systems, 2003, pp. 513-519
Kohlbauer, R.; Hagenah, H.; Geiger, M.:
Process design for hydroforming of sheet metal pairs using a closed loop controlled finite element simulation.
In: Shirvani, B.; Geiger, M.; Kals, H.J.J.; Singh, U.P. (Edtrs.): Proceedings of the 10th International Conference on Sheet Metal, SheMet 2003, University of Ulster, 2003, pp. 219-226
Hagenah, H.:
Simulationsbasierte Bestimmung der zu erwartenden Maßhaltigkeit für das Blechbiegen.
Fertigungstechnik Erlangen, Band 141, : Meisenbach, 2003
Wurm, T.; Menzel, T.; Müller, B.; Hagenah, H.; Geiger, M.:
The use of kinematic chains and construction catalogues for an advanced design of complex actuator geometries in micro adjustment.
In: Kjellberg, T. (Edtr.): Proceedings: International CIRP Design Seminar: Design in the New Economy; Design Theory, Methodology and its Intergration with the Computational Tools to support Teams of Competence, KTH Stockholm, 2001, pp. 417-421
Menzel, T.; Hagenah, H.:
Knowledge Based Approach for Intelligent Design of Manufacturing Processes.
In: Bothe, H.; Fyfe, C. (Edtrs.): Proceedings of the EIS'2000. Second ICSC Symposium on Engineering of Intelligent Systems, ICSC Academic Press, 2000, pp. 327-333
Geiger, M.; Hagenah, H.; Menzel, T.:
Simulation based optimisation of the accuracy of sheet metal bending parts caused by the manufacturing plan.
In: Teti, R. (Edtr.): Proceedings of the 2nd CIRP International Seminar of Intelligent Computation in Manufacturing Engineering ICME 2000, 2000, pp. 283-290
Hagenah, H.; Knoblach, J.:
Bewertung von Fertigungsplänen der Blechverarbeitung in Abhängigkeit von der erreichbaren Bauteilgenauigkeit.
In: Lehnert, W. (Edtr.): Qualitätsfaktor Umformtechnik: Tagungsband der 5. Sächsischen Fachtagung Umformtechnik in Freiberg, Technische Universität Bergakademie, 1998, pp. 16.1-16.15
Hagenah, H.; Backes, F.:
Computer aided estimation of achievable accuracy for bending parts.
In: Geiger, M.; Shirvani, B.; Sing, U.P. (Edtrs.): Sheet Metal 1998: Proceedings of the 6th International Conference on Sheet Metal, Twente University Printers, 1998, pp. 199-208